How To Remove Battery From Iphone Se

Follow along on this pic guide to supervene upon the battery in your iPhone SE! I tell you well-nigh all the 'gotchas' involved in this battery replacement, so you can one time again take a telephone that lasts the whole day without requiring multiple re-charges!

Background

I bought a refurbished  iPhone SE off of Amazon, and the battery life was non good. Looking in the "Bombardment Health" department of the settings, it said the maximum battery capacity was only 71%. Practically speaking, that meant that later on a total charge to 100%, the phone would last for about i.5 hrs so be down to 35%! It was necessary to alter the bombardment.

I was wondering what it would be like, and if I would damage the phone in the procedure. It seemed like the new battery reviews on Amazon were either that it went great and worked perfectly, the phone was somehow damaged in the process, or the new battery life was no better than the bombardment that was being replaced…

Obviously I was hoping for the first outcome. Well, I went ahead and took a chance, and information technology worked out great! Replacing the bombardment is non as piece of cake as just removing a couple screws and plopping it in. BUT if yous take your time, have photos to reference, and are at least marginally mechanical, you should have no trouble at all replacing the bombardment in your iPhone SE!

Okay, let's go started!

Tools and Supplies:

• heating pad or hair dryer
• new battery kit (iPhoneSE)

Step-by-Step Instructions

I ordered a battery and repair kit package off of Amazon. This one is a 2180 mAh battery which has a little more than juice than the original bombardment in the iPhone SE has.

The kit includes the replacement bombardment, the agglutinative, and a variety of tools necessary to complete the repair.

Below is shown the tools included in the kit (except for the instruction canvas).

Note: the kit has changed slightly since I originally posted this. The kit now has a few different tools, simply still has everything needed for the battery replacement. Check this link for pictures of the currently-included tool set up.

The first footstep is to turn off the phone. Discharge the phone then it is at less than 15% charged, press and hold the power push, then apply the on-screen prompts to slide the slider to turn off the telephone.

Next, take out the SIM card. This is a precautionary pace, and then it doesn't get damaged or erased while irresolute the battery. If you don't accept the special tool, use a newspaper clip to push in at the hole, until the SIM tray comes out. Remove the SIM carte and the tray.

I recommend using a heating pad or a hair dryer to carefully estrus upwards the back of the phone in club to loosen the adhesive that the battery is glued to the back of the phone with. Don't over-do the heat, but a low heat setting can help to loosen the adhesive. Besides, if using a pilus dryer, await until you become to that step before heating the phone. Again, don't over-practice this! you lot just want to get it comfortably warm, not hot!

Utilise the pentalobe screwdriver that is included in the kit to remove the 2 screws on either side of the charging port.

Utilise fifty-fifty force per unit area. Don't strip the screws.

Tip: Put the screws into some sort of container. In the end, you volition take eight screws of varying sizes. Keep them separate so that y'all know where they go when it comes time to put your telephone back together.

Next, put the suction cup on the screen just in a higher place the home button. You will use this to gently pull up on the screen as you pry the screen upward. Apply ane or more of the plastic prying tools to gently scrape the mucilage from the seam between the metal and the glass part of the screen.

Get all the mode effectually the screen, using the corner of the plastic tool. Press the tool into the seam to begin to get information technology to dissever.

Tip: Take your time with this footstep! This is where people damage the connection to the habitation button. If you lot rip the screen off too difficult and fast, the connector will be broken, and your home push button volition no longer work! You lot can also pause the screen hither if you are non careful. Scrape around the edge, and use gentle upward force per unit area on the screen (with the suction cup).

Once you have worked the tool effectually the lesser border of the phone between the metal sides and the glass screen while pulling upward on the suction cup, y'all will notice the screen starting to come up up a little bit.

There is a slight indentation on the left-manus side, where yous can fit a plastic prying tool.  Find that extra bit of gap in the image below. Use that as the offset point where you offset prying. But pry gently, and piece of work your fashion back and forth along the bottom of the phone.

Information technology helps to gently twist the plastic tool in order to slightly lift the screen. Don't lift the screen up all the fashion, nonetheless!

Once the screen has come up a bit, do not elevator information technology more than than most three/iv″. There is a connector that we demand to disconnect. In that location is a ribbon cable going from the home push button on the screen to this connector.

You demand to remove the metal cover, seen near the center of the prototype below.

Apply a tweezers to gently lift upwardly on the metal protective comprehend.

Once you accept removed the metal protective cover, employ a plastic pry tool to gently elevator the edge of the connector apart.

Once the ribbon cablevision is disconnected, tip the screen upwards.

You will at present need to remove 6 tiny Phillips screws. They are shown in the circles beneath.  Use the tiny Phillips screwdriver included in the kit.

Tip: Go on track of which spiral goes where. Some of the screws are longer, and some are shorter. You'll be glad you did when you are putting this back together.

Remove the 6 screws, and as you practice, 2 metal plates will come off. Set those aside for at present.

Next, use one of the plastic tools to gently pry up the bombardment connector, as shown.

Now, gently pry up the iii connectors going to the screen, so that the screen can be removed.

This shows the 3 connectors going to the screen, after the screen has been removed.

carefully set the screen aside while we work on removing the bad bombardment.

At the top edge of the battery, is a minor fold of what looks like cardboard plastic. Gently pull this upward with one of the plastic tools.

The paper-thin piece of plastic is really a grip to remove the adhesive that isbelow the battery. Grip the adhesive, and start gently pulling it out.

Keep pulling, with steady even pressure. Utilize your other hand to agree the phone steady.

One time the adhesive bands come up out, the battery will easily elevator out of the phone.

Here is a shot of the new and onetime battery, side-past-side.

Next, accept the adhesive strips. Remove the plastic on 1 side, and place them into the battery slot.

Tip: Brand sure that the blackness plastic grip is at the superlative end. Place the black cease in offset, so that it is even with the top of the battery slot.

One time the adhesive has been placed down, remove the top sheet of protective plastic.

Now, take the new bombardment and place information technology into the slot. You but take 1 shot at this, so make sure that y'all have it oriented with the battery connector cable in the right spot!

Tip: If anything, put the bombardment closer to the bottom of the compartment. This ensures that the ribbon cablevision to the connector volition reach.

Now, carefully line up the battery connector, so printing information technology down until information technology snaps into place.

Hither is a shot of the new bombardment installed.

Next, employ the screwdriver to put the metal bracket back over the battery connector. The screwdriver in this battery replacement kit is magnetized, which is very helpful!

Update: I am not sure if the currently supplied screwdriver is magnetic.

Utilise the magnetized screwdriver to place the screw into the hole.

Then screw it down.

Tip: Don't over-tighten whatever of the screws. They are in that location to concord the protective encompass in place and that is it. Over-tightening the screws can take unintended consequences!

We're at present set to put the screen back on. These are the 3 connectors that will need to be re-continued.

Agree the screen straight up, while y'all line up the connectors onto their ports. Brand sure they are aligned properly, then, one by one, press them down until they snap lightly into identify.

Tip: Make sure the connectors are lined upwardly properly! Position the connector over its port, then lean down and look at it from the edge to ensure the pins are lined upwardly as well as you lot tin can. Take your time! If you are pressing on the connector, and it won't become, lift it upwards, examine where you are placing it, then try again!

Employ one of the plastic tools to make sure the connectors are tight.

Position the metal protective cover over the screen connectors, and put in the four screws to concur it downwardly. Don't over-tighten the screws.

Once all the screws are in, examine your work to make sure you didn't miss any connectors or screws. Carefully blow out any dust or lint that found its way into the phone.

Gently lower the screen. Nosotros demand to re-connect the dwelling house-button connector.

Line upwards the connector, and utilize one of the plastic tools to press information technology downwards.

We now need to put the minor metal protective cover dorsum on. This was the most time-consuming part of the job for me, mostly because I couldn't recollect exactly how it went back on! That is why I am including several pictures of this connector here!

Utilise the tweezers to position the metal cover over the connector. It works best if theback finish of the connector is in first, and then the forepart is pressed down.

Past 'back' end, I mean the side on the left in the picture beneath. Once the back finish is in, then press the forepart end until information technology snaps into identify.

Adjacent, gently press the screen down all the way around the telephone. Put the 2 screws back in with the pentalobe screwdriver.

Plow the phone on, and verify the functionality of all the buttons and the touchscreen.

Navigate to the "Battery Wellness" screen in the settings and check that the maximum capacity is 100%!

There are a couple more than steps to finish things off. Start, power downwards the phone and put the SIM card back in.

Next, we need to calibrate the battery in order to requite your phone optimal performance. To exercise this, drain the battery below 5% through normal use, so turn the phone off and charge it uninterrupted to 100%. Repeat this 2-3 times.

Hey, I hope this helped yous out! Nothing amend than spending ~$20 instead of buying a whole new phone!

If yous performed a bombardment alter, let the states know most it in the comments! What was the nigh hard role for you? I'd love to hear it!

Tools and Supplies Used:

• heating pad or hair dryer
• new battery kit (iPhoneSE)

How To Remove Battery From Iphone Se,

Source: https://practicalmechanic.com/2019/10/13/how-to-change-the-battery-iphonese/

Posted by: brewerhistat.blogspot.com

Share this post